6.5 Creedmore and Re16?

Get or give advice on equipment, reloading and other technical issues.

Moderator: Mod

Message
Author
ShaneG
Posts: 574
Joined: Fri Jun 15, 2012 2:25 pm
Location: Cairns

6.5 Creedmore and Re16?

#1 Postby ShaneG » Sat Dec 22, 2018 9:04 am

Is there anyone here who has direct experience with Reloader 16 and the 6.5 Creedmore cartridge please?
Not a lot of info about
I missed the 130 Bergers but have Lapua Scenar 123gr; Scenar L in 120gr and 136gr to try?

bobbyaxe
Posts: 37
Joined: Sun Jan 28, 2018 1:07 pm

Re: 6.5 Creedmore and Re16?

#2 Postby bobbyaxe » Sat Dec 22, 2018 10:18 pm

I use 140gr ELD match in Norma Brass.

At the moment I'm using 42.1grs of RL16 and get around 2900fps.

The SD is also quite low as well.

The hottest load I've tried is 43.2grs and there was no pressure signs so could probably go further.

https://sierrabulletsblog.com/2017/01/0 ... load-data/

ShaneG
Posts: 574
Joined: Fri Jun 15, 2012 2:25 pm
Location: Cairns

Re: 6.5 Creedmore and Re16?

#3 Postby ShaneG » Thu Dec 27, 2018 10:14 am

bobbyaxe wrote:I use 140gr ELD match in Norma Brass.

At the moment I'm using 42.1grs of RL16 and get around 2900fps.

The SD is also quite low as well.

The hottest load I've tried is 43.2grs and there was no pressure signs so could probably go further.

https://sierrabulletsblog.com/2017/01/0 ... load-data/


What length barrel please?
Just running initial loads in a 24" Tikka CTR today and have topped out in pressure at 43gr Re16 and 136 Lapua Scenar L? Vo only 2730fps?
This is with Lapua SR primer cases.
Will try Lapua 123 and 120gr L next

bobbyaxe
Posts: 37
Joined: Sun Jan 28, 2018 1:07 pm

Re: 6.5 Creedmore and Re16?

#4 Postby bobbyaxe » Sun Dec 30, 2018 7:18 pm

In using a 24inch Howa 1500 heavy varmint.

I'll post the velocities from my ladder test on Thursday night when I'm back at the desk.

I'm also using federal 210m primers.

bruce moulds
Posts: 2900
Joined: Sun Jun 19, 2005 4:07 pm

Re: 6.5 Creedmore and Re16?

#5 Postby bruce moulds » Mon Dec 31, 2018 11:19 am

creedmoor
"SUCH IS LIFE" Edward Kelly 11 nov 1880
http://youtu.be/YRaRCCZjdTM

SunnyCoast 5r
Posts: 202
Joined: Sun Oct 25, 2015 10:23 pm

Re: 6.5 Creedmore and Re16?

#6 Postby SunnyCoast 5r » Wed Jan 02, 2019 8:09 pm

A bit off topic but....

ShaneG I finally got the 6.5 Tikka to the range with some factory ammo...the Federal 140gn at 100y was pretty good in a little reprieve from a gusty crosswind at Belmont SSAA!
DBEC9D76-D8B0-4CCB-8E11-7F6A2A7BA7D5.jpeg
You do not have the required permissions to view the files attached to this post.

bobbyaxe
Posts: 37
Joined: Sun Jan 28, 2018 1:07 pm

Re: 6.5 Creedmore and Re16?

#7 Postby bobbyaxe » Wed Jan 02, 2019 9:15 pm

Apologies my previous data above was incorrect

Everything below is on 5 shots
@41.0gr avg 2690fps - SD 8.1
@41.4gr avg 2713fps - SD 6.4
@41.8gr avg 2740fps - SD8.3
@42.1gr avg 2760fps - (on 3 shots- 2 didnt register)
@42.5gr avg 2774fps - (only 3 shots registered)
@42.9gr avg 2805 - SD4.3
@43.2gr avg 2823 - SD 2.8

Norma Brass (Virgin)
Federal 210M primers
140 ELD Match pills

ShaneG
Posts: 574
Joined: Fri Jun 15, 2012 2:25 pm
Location: Cairns

Re: 6.5 Creedmore and Re16?

#8 Postby ShaneG » Thu Jan 03, 2019 12:53 pm

SunnyCoast 5r wrote:A bit off topic but....

ShaneG I finally got the 6.5 Tikka to the range with some factory ammo...the Federal 140gn at 100y was pretty good in a little reprieve from a gusty crosswind at Belmont SSAA!DBEC9D76-D8B0-4CCB-8E11-7F6A2A7BA7D5.jpeg

Hey Peter
Try the Fusion if possible as well? It is much cheaper than it used to be as Federal dropped the price last year although the BC is not that great?
I have also tried the Federal 130gr Berger without great results?
It does have approx .140" jump on my Tikka throat? I even pulled some partially to reseat at .010" jump but no joy?

I have just found two very promising results with 120gr Scenar L and 123gr Scenar and Re16!
Next step is try at our first club shoot Sunday week at 300M?
These look like a possible 600M useful load considering velocity and BC?
Should be useful at shorter ranges PRS?

ShaneG
Posts: 574
Joined: Fri Jun 15, 2012 2:25 pm
Location: Cairns

Re: 6.5 Creedmore and Re16?

#9 Postby ShaneG » Thu Jan 03, 2019 12:55 pm

bobbyaxe wrote:Apologies my previous data above was incorrect

Everything below is on 5 shots
@41.0gr avg 2690fps - SD 8.1
@41.4gr avg 2713fps - SD 6.4
@41.8gr avg 2740fps - SD8.3
@42.1gr avg 2760fps - (on 3 shots- 2 didnt register)
@42.5gr avg 2774fps - (only 3 shots registered)
@42.9gr avg 2805 - SD4.3
@43.2gr avg 2823 - SD 2.8

Norma Brass (Virgin)
Federal 210M primers
140 ELD Match pills


I really questioned the 2900 fps claim? I think I have a "slow" barrel which could speed up after a few 100 rounds however I ran into max pressure with 43.0 gr Re16 and only 2735fps.
This is with Lapua SR brass

Mozzie
Posts: 127
Joined: Sun Feb 11, 2018 5:47 pm
Location: Cairns

Re: 6.5 Creedmore and Re16?

#10 Postby Mozzie » Thu Jan 03, 2019 6:44 pm

Shane
I’ve had no great results with the 136 scenar L, 45 through 20 off lands with 2209. Do you have any info on the 2 promising loads you would like to share ?
Cheers
Mozzie
My truck doesn’t run on love, it runs on diesel.
However, I love my rifle and it runs on lead. #-o

bobbyaxe
Posts: 37
Joined: Sun Jan 28, 2018 1:07 pm

Re: 6.5 Creedmore and Re16?

#11 Postby bobbyaxe » Thu Jan 03, 2019 10:18 pm

I may be wrong, but would the small primers in the lapua brass, drop the velocity.

I was chatting to a guy at Raglan and he suggested that using magnum primers may offer an extra 50fps over a normal match primer, though I haven't had the chance to test this yet.

Buckshot
Posts: 42
Joined: Sat Dec 29, 2018 9:19 pm

Re: 6.5 Creedmore and Re16?

#12 Postby Buckshot » Fri Jan 04, 2019 6:26 am

Hi bobbyaxe, I see you managed to get the higher 2800+ node in the howa, what would you expect an average group size to be at 300yd compared to the lower velocity charges? I saw groups open up in my howa 26 inch with ar2209/H4350 above 41.7 grains along with pressure signs. Interestingly, I also saw short range groups shrink as the bullet was seated much farther out from lands. I tested out to .210 jump with best groups at .210. Not sure if it was the jump or the actual crush on the powder that helped. The young bloke in at the gunshop in town went the other way in his tests in his creedmoor. He found a very accurate short range load at 37.5 grains ar2209 with 129grain projectiles.

Im interested in fiddling with reloader powder to find a good 600-900 yard load but most group testing ive seen online so far had good velocity but poor groups at 300 yards. Whats your findings on this ? Following this thread with interest.

ShaneG
Posts: 574
Joined: Fri Jun 15, 2012 2:25 pm
Location: Cairns

Re: 6.5 Creedmore and Re16?

#13 Postby ShaneG » Fri Jan 04, 2019 9:07 am

bobbyaxe wrote:I may be wrong, but would the small primers in the lapua brass, drop the velocity.

I was chatting to a guy at Raglan and he suggested that using magnum primers may offer an extra 50fps over a normal match primer, though I haven't had the chance to test this yet.


I have not tested this in the 6.5 CM however from extensive testing in 308 Palma brass i have seen no velocity change between CCI450 magnum; BR4 and S&B SR.
If anything the BR4 gave slightly higher Vo than the 450! The main difference is in ES and BR4 and S&B are both very good.

The main change from LR brass to Palma is that typically Palma requires between .8 and 1.0 gr extra powder than LR brass to equal pressure / velocity.
My main reason to use Palma in 308 is case life and I am getting very low ES.
So with SR available for the 6.5CM I thought I would trial same.

ShaneG
Posts: 574
Joined: Fri Jun 15, 2012 2:25 pm
Location: Cairns

Re: 6.5 Creedmore and Re16?

#14 Postby ShaneG » Fri Jan 04, 2019 9:12 am

Mozzie wrote:Shane
I’ve had no great results with the 136 scenar L, 45 through 20 off lands with 2209. Do you have any info on the 2 promising loads you would like to share ?
Cheers
Mozzie


Mozzie
I did not get anything to write home about with 136L either.
Both the 120L and 123 are looking excellent with the Lapua SR brass and Re16.
Briefly tried 2209 but Re16 about 50 fps faster at same pressure!

I am loath to publish the load as it is max in my rifle.

Same load both pills .010 jump.
And with that OAL still fits the CTR magazine!
Give me a call at the shop if you want?

lee_enfield223
Posts: 142
Joined: Fri Apr 29, 2016 6:38 pm
Location: SYDNEY Australia

Re: 6.5 Creedmore and Re16?

#15 Postby lee_enfield223 » Sat Jan 05, 2019 4:25 pm

I have tried 2209 and rl 16 in my 6.5 creedmoor custom 24inch stiller actioned rifle and only got 2680 max, and was getting 1moa groups, at max loads but dropped the loads to about 41grs of 2209 and getting..Just over half MOA, still was not happy, ended up trying Winchester 760 and what a huge difference in accuracy!!! I am still getting about 2620fps with 41grs behind a nosler 140gr CC but am now shooting under 1/2 MOA all day, and just decided to go to a friend's farm and shot at 325m and using 41grs of 760 and getting 1.2 inch groups of 5 shots, I really don't think that the creedmoor is designed for speed,and you need to run 120grs projectiles to get 3000fps


Return to “Equipment & Technical”

Who is online

Users browsing this forum: No registered users and 44 guests